Gearing up for a Successful Hay Season
Ongoing drought conditions and hay shortages have made the need
for good quality forage crucial. Specific management practices are necessary to
maintain hay quality and minimize hay loss during harvest, transportation, and
storage of large round bales. The following helpful tips will ensure that when
the hay is ready in the field you and your equipment will be too!
Windrower Inspection:
- · Sickle-bar headers: Replace cutter bar teeth and
ledger plates. Replace the guards once yearly.
- ·
Disk mowers: Replace knives and rotate or replace worn
turtles covering the knives. Proper blade maintenance is critical to achieving
a good cut. Blades must be sharp to cut the forage cleanly and to minimize stem
and leaf shattering. Grease all lift system wear points. Check all belts for
signs of wear and check the tires and tire pressure to insure proper inflation.
- ·
Self-propelled machines: Change engine oil and
filters, and blow out all air filters, including the cab air filter. Make sure
the radiator is free of dirt and debris. Stock up on key replacement parts such
as cutter blades, sickles sections, guards, drive belts and hoses.
Round Baler Inspection:
- ·
Grease all of the grease zerks on wear points
and chain lubricating.
- ·
Inspect the belts on your baler for damage. The
belts should be running straight and not coming into contact with other belts
of side sheets of the baler. Many times the belts can stretch and need to be
resized to proper length. Be sure to take the belts off and measure them every
two years to ensure they are all the same length (plus or minus one inch). Also
check the lacings on the belts every 800-1,000 bales.
- ·
Check the chain to ensure proper length is
maintained. Over time the movement of the chain over the sprockets will cause
the pins and rollers to wear and become elongated or oval-shaped. If this
happens the pitch of the chain will change because of the increased length. At
only 3 percent extension the chain should be replaced to avoid failure.
- ·
Replace any broken pickup tines.
- ·
Check gearbox fluid levels and change if
necessary. Run the baler for about a half hour and then check the temperature
of the bearings with an infrared temperature gun.
Cutting hay:
Cut hay after the dew is gone and when the topsoil is dry to reduce soil
compaction and hasten hay drying. A long stubble keeps the windrow off the soil
surface to aid drying and improve subsequent pickup performance. Research shows
hay quality is increased when hay is cut while the sugar content remains higher
in the plant. Cutting late morning or early afternoon will result in lower
quality hay as the plant sugar content decreases with increased air
temperatures. Choose the right blade for the job. A shallower 10 or 11 degree
blade creates less air lift thus pulling less dirt into the forage. Thick
matted forage may require a blade with more lift such as an 18 degree blade.
Set the cutter height between 1.5 and 3 inches. Avoid pitching the cutter bar
downward at too steep of an angle to reduce dirt contamination and knife wear.
Ideally, the cutter will gently float across the ground without scuffing the
surface. If you see scuffs across the field you don’t have enough flotation
pressure, or the mower is set too heavy. If you see waves in the field, you
have too much flotation pressure, or the header is set too light. If the field
surface is rough and uneven, flotation should be increased making the head
lighter to glide over rough terrain.
Conditioning:
Conditioning speeds drying by opening the waxy cuticle layer surrounding the
stem to allow moisture to evaporate faster. Hay conditioning can reduce drying
time by two to five days. Correctly adjust the conditioners to maintain
adequate roll pressure uniformly along the entire roll length. The roll gap is
one of the most crucial adjustments for the conditioner. Apply enough pressure
to the hay to cause a noticeable break in the stem skin, but not so much
pressure that leaves are broken off. In general the roll gap should be at 1/16
inch or less. Set the roll tension tight enough to achieve a consistent roll
gap, if the crop is being over-conditioned then reduce the tension. Keep the
rolls clean and free of material. Check and make sure the roll is not worn down
in the center and replace the worn rolls if necessary. It is essential to
maintaining uniform pressure on the conditioner roll. Adjust the swath board to
match the width of the baler pickup. Make the windrow width as wide as
possible; it should be at least half the width of the baler pickup to minimize
baler loss. Ideally the swatch should be nearly the full width of the baler
pickup.
Raking and Windrow Formation:
Raking can form swathed hay into a windrow or accumulate two or more windrows
into one. More leaf loss can be caused by raking hay than by any other harvest
operation. When raking, synchronize the field speed and PTO speed to provide a
gentle lifting and turning action. This will help avoid aggressive handling of
the forage and excessive leaf loss. Set rake tines to skim just above the ground
so they don’t dig up dirt, there should be one-half to one inch of ground
clearance at all times. To form bales of consistent density and shape, make
windrows uniform in width and uniform in the amount of hay contained. As
mentioned previously it is best to create a windrow as large as possible to
meet the baler pickup capacity and reduce field loss. Loss occurs as the bale
turns within the bale chamber, so try not to run the baler when there is no hay
feeding into the chamber to reduce unnecessary hay loss.
Baling:
When hay is baled, moisture content should be no higher than
18-22 percent. The higher the moisture content the less loss will occur so try
to bale with the maximum moisture content without going above 20 percent to
prevent spoilage. Synchronize the field speed to the pickup rotational speed to
reduce pickup loss. If forward speed is too slow, the pickup device snatches
the hay and pulls the windrow apart as it feeds. Or, if the forward speed is
too fast the hay will start to bunch up in front of the pickup. The windrow
should flow into the baler with minimum disruption. The operator should follow
a weaving pattern to fill each side of the baler with crop material evenly. The
feed rate should be as high as possible to minimize the number of turns within
the bale chamber. A high feed rate can be attained by using large windrows and
high forward speeds. Where windrows are small or field speeds must be slow, use
a lower PTO speed.
.jpeg)
.jpeg)
